UP AND RUNNING BASICS
Below are a few pointers to help you set up (a.k.a. pair) your new G1 WiFi Gateway when it arrives. If you have a G2 WiFi Gateway, the steps in the app are very similar, but see the notes for the G2 at the end of this article.
- Make sure you have the latest version of the SensorPush app from the Apple App Store or Google Play Store.
- Once you've downloaded or updated the app, remove the Gateway and power adapter from the packaging.
- Verify that your WiFi network is using 2.4GHz or is in "dual band" mode (both 2.4GHz and 5GHz). 2.4GHz is the most common type of WiFi, so if you are unsure, you likely already have 2.4GHz.
- Locate the Gateway somewhere central to the sensors you want to monitor so the Gateway has the best chance of picking up the signals coming from the sensors. Power up the Gateway with the included adapter and raise the antenna. After it starts up, you should see a steady blue light on the front.
- Open the SensorPush app to the main screen (the main screen says "Devices" at the top) and tap the add button in the top-right corner. This is the same button used to add sensors. It will present you with a choice to add a sensor or a gateway. Tap "Add Gateway."
- Hold your phone within a few feet of the Gateway. The phone will form a temporary connection to the Gateway. This might take a minute or two. If it takes longer than that, please try restarting the phone and the Gateway and trying again.
- Once you're connected, you'll be prompted to create an account (tap "SIGN UP") or log in if you already have one. If you only see "LOG IN" and the app says the Gateway is already paired to another account, see My Gateway is locked to another account.
- Next, choose a WiFi network and enter a password (if necessary). After the Gateway has connected you should see a green checkmark next to the network in the list. If your network isn't listed (for example, a hidden network), tap "Join Other Network" at the bottom of the list and type its name.
Note: If you have an older router and a hex-based WEP password, you must put the prefix "0x" in front of the password (the "0" in "0x" is a zero). - You can also connect via Ethernet instead of using WiFi. Just plug in the Ethernet cable (DHCP is required) and wait for the "Connected via Ethernet" message to appear on the Gateway configuration screen. If your sensors stop updating after you plug in or unplug the Ethernet cable, unplug the Gateway's power for a few seconds and plug it back in.
- Give your Gateway a name if you like and you're all set.
- Please try to keep the app up to date for best performance.
If the Gateway won't connect to your WiFi, see My Gateway won't connect to WiFi. If you have sensors that also need setup, refer to the sensor setup instructions.
You should now be able to monitor your sensors over the internet. You can test this by turning the Bluetooth off on your mobile device. Provided all of the sensors are in range of the Gateway, you should be able to see them update in the app roughly once per minute. A small icon shaped like the Gateway will appear to the right of the sensor's name if the sensor is communicating via the Gateway. You can also verify that the information is up to date by looking at the "Last seen" time right beneath the sensor's name on the list of devices in the main screen of the app. Readings should be within the last couple of minutes of the current time if the sensor is communicating normally through the Gateway.
While the app is open it updates automatically, but you can also refresh the data by doing a pull-down refresh (a.k.a. "swipe-down-to-refresh") on the main screen of the app. A pull-down refresh is the same thing you can do in an email app where you use a finger to pull down on the screen to check the server for new emails. This should load any new sensor and Gateway data from the SensorPush cloud.
You may want to experiment a bit with the placement of your Gateway and the antenna and sensor orientations for optimal coverage in your particular situation. Give the Gateway some time (half an hour or so) in each configuration to scan and communicate with all of the sensors before evaluating it or trying something else. The initial download takes longer than the following incremental updates, so while you should start to get current conditions very quickly, it might take some time for the Gateway to catch up with the history stored on the sensor. For placement tips, see What is the wireless range of SensorPush sensors?
Bluetooth in the SensorPush App
When you sign in to your account, the SensorPush app turns off its own Bluetooth access, since your sensors now report through the Gateway. This does not turn off the Bluetooth of your mobile device in general. If you want to use a sensor outside the range of the Gateway (e.g. taking it on a hike), or add a new sensor, turn Bluetooth back on inside the SensorPush app. Readings your phone collects over Bluetooth are saved in the app on that phone, but they are not uploaded to the cloud. Here is how to turn Bluetooth access on and off inside the SensorPush app:
- Open the app, and from the main "Devices" screen select the button in the top left to open app settings.
- Once in app settings you'll notice a section called "Configuration" with a switch for Bluetooth.
If You Have a G2 WiFi Gateway
- The G2 connects over 2.4GHz WiFi only (it has no Ethernet port). It supports WPA2 and WPA3 networks.
- Out of the box, the G2's light cycles through colors. It pulses blue while your phone is connected to it, blinks red when it isn't connected to WiFi, blinks purple when it's on WiFi but can't reach the SensorPush cloud, and pulses white when everything is working. It's normal to see red and purple for a few seconds after it starts up.
- The G2 talks to one phone at a time. If the app can't find it, close the SensorPush app on any other phones nearby and try again.
Finally, as always, we're here to help. Let us know if anything isn't working as you expect or is unclear or confusing. We're always working to improve our products and your feedback is critical to make them the best they can be. Contact us at: support@sensorpush.com